High-Quality Perovskite Materials Developed Capable of Utilizing Long-Wavelength Sunlight

Moving toward the Realization of Low-Cost, High-Efficiency Solar Cells

2015.08.19
(2015.11.02 Update)


National Institute for Materials Science (NIMS)

A NIMS research group has developed the new method to fabricate high-quality perovskite materials capable of utilizing long-wavelength sunlight of 800 nm or longer.

(The study was published in Advanced Materials on July 14, 2015: J. Liu, Y. Shirai, X. Yang, Y. Yue, W. Chen, Y. Wu, A. Islam and L. Han: High-quality mixed-organic-cation perovskites from a phase-pure non-stoichiometric intermediate (FAI)1—xPbI2 for Solar Cells, DOI: 10.1002/adma.201501489.)

Abstract

  1. A NIMS research team led by Liyuan Han, director of the Photovoltaic Materials Unit, has developed the world’s first method to fabricate high-quality perovskite materials capable of utilizing long-wavelength sunlight of 800 nm or longer. Compared to conventional methods, this method enables the creation of perovskite materials that have a 40-nm wider optical absorption spectrum, a high short-circuit current and high open-circuit voltage. Thus, this method is regarded as a new approach to enhance the efficiency of perovskite solar cells.
  2. The currently available perovskite solar cells possess optical absorption spectra skewed toward shorter wavelengths. To improve the energy conversion efficiency of these cells, it is vital to develop perovskite materials with optical absorption spectra expanded to include longer wavelengths. Accordingly, several research institutes are developing perovskite materials, (MA)xFA1—xPbI3, which include two types of cations, MA and FA, capable of absorbing light in the longer wavelength region. However, these cations have demerits: their mixing ratio and crystallization temperature are difficult to control. Moreover, due to their tendency to form a mixed crystal phase, there had been no effective method established to fabricate high-purity, single-crystalline perovskite materials.
  3. To resolve these issues, we developed a new method to fabricate a new type of mixed cation-based perovskite material. We first fabricated a pure, single-crystalline precursor material, (FAI)1—xPbI2, under altering temperatures. Then, we performed a reaction between the precursor and MAI (methylammonium iodide). The resulting perovskite material, (MA)xFA1—xPbI3, was a single crystalline phase and had a long fluorescence lifetime. These observations indicated that electrons in the material rarely recombine and they have long lifetimes. The optical absorption spectrum of the solar cells employing this material covered up to 840 nm, which was 40 nm wider than the spectrum of conventional perovskite material (MA3PbI3). As a result, the solar cells we developed obtained 1.4 mA/cm2 higher short-circuit current than the MAPbI3 solar cells that were manufactured under the same conditions.
  4. In future studies, we intend to develop high-quality perovskite solar cells capable of utilizing a broader spectrum of sunlight by adjusting the ratio of the two cations.
  5. A part of these results were obtained through research activities under the research topic “Device physics of dye-sensitized solar cells” in the research area “Creative research for clean energy generation using solar energy” (Research Supervisor: Masafumi Yamaguchi, Principal Professor, Toyota Technological Institute) specified in the Core Research of Evolutional Science and Technology (CREST) program sponsored by the Japan Science and Technology Agency (JST).

"Figure: (a) Fabrication method for a high-quality perovskite material; (b) X-ray diffraction patterns of perovskite materials prepared with different methods. The x-axis represents the intensity of X-ray diffraction while the y-axis denotes the X-ray diffraction angle." Image

Figure: (a) Fabrication method for a high-quality perovskite material; (b) X-ray diffraction patterns of perovskite materials prepared with different methods. The x-axis represents the intensity of X-ray diffraction while the y-axis denotes the X-ray diffraction angle.



Contacts

(Regarding this research)

Liyuan Han
Photovoltaic Materials Unit
National Institute for Materials Science
Tel: +81-29-859-2305
Fax: +81-29-859-2304
E-Mail: HAN.Liyuan=nims.go.jp
(Please change "=" to "@")

(Regarding public relations)

Public Relations Office
National Institute for Materials Science
1-2-1 Sengen, Tsukuba, Ibaraki, 305-0047, JAPAN
Tel: +81-29-859-2026
Fax: +81-29-859-2017
E-Mail: pressrelease=ml.nims.go.jp
(Please change "=" to "@")